DS1825U+T&R【PDF 9/21 页】IC THERMOMETER DIGITAL 8-USOP

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录39

5页 6页 7页 8页 [9页]10页 11页 12页 13页

DS1825 Programmable Resolution 1-Wire Digital Thermometer With 4-Bit ID

9 of 21

Table 4. THERMOMETER RESOLUTION CONFIGURATION

Resolution

Max Conversion Time

9-bit

93.75ms

CONV

/8)

10-bit

187.5ms

CONV

/4)

11-bit

375ms

CONV

/2)

12-bit

750ms

CONV

)

CRC GENERATION

CRC bytes are provided as part of the DS1825s 64-bit ROM code and in the 9

byte of the scratchpad memory.

The ROM code CRC is calculated from the first 56 bits of the ROM code and is contained in the most significant

byte of the ROM. The scratchpad CRC is calculated from the data stored in the scratchpad, and therefore it

changes when the data in the scratchpad changes. The CRCs provide the bus master with a method of data

validation when data is read from the DS1825. To verify that data has been read correctly, the bus master must re-

calculate the CRC from the received data and then compare this value to either the ROM code CRC (for ROM

reads) or to the scratchpad CRC (for scratchpad reads). If the calculated CRC matches the read CRC, the data has

been received error free. The comparison of CRC values and the decision to continue with an operation are

determined entirely by the bus master. There is no circuitry inside the DS1825 that prevents a command sequence

from proceeding if the DS1825 CRC (ROM or scratchpad) does not match the value generated by the bus master.

The equivalent polynomial function of the CRC (ROM or scratchpad) is:

CRC = X

+ X

+ 1

The bus master can re-calculate the CRC and compare it to the CRC values from the DS1825 using the polynomial

generator shown in Figure 9. This circuit consists of a shift register and XOR gates, and the shift register bits are

initialized to 0. Starting with the least significant bit of the ROM code or the least significant bit of byte 0 in the

scratchpad, one bit at a time should shifted into the shift register. After shifting in the 56

bit from the ROM or the

most significant bit of byte 7 from the scratchpad, the polynomial generator will contain the re-calculated CRC.

Next, the 8-bit ROM code or scratchpad CRC from the DS1825 must be shifted into the circuit. At this point, if the

re-calculated CRC was correct, the shift register will contain all 0s. Additional information about the Dallas 1-Wire

cyclic redundancy check is available in Application Note 27 entitled Understanding and Using Cyclic Redundancy

Checks with Dallas Semiconductor Touch Memory Products.

Figure 9. CRC GENERATOR

1-Wire BUS SYSTEM

The 1-Wire bus system uses a single bus master to control one or more slave devices. The DS1825 is always a

slave. When there is only one slave on the bus, the system is referred to as a single-drop system; the system is

multidrop if there are multiple slaves on the bus.

All data and commands are transmitted least significant bit first over the 1-Wire bus.

The following discussion of the 1-Wire bus system is broken down into three topics: hardware configuration,

transaction sequence, and 1-Wire signaling (signal types and timing).

(MSB)

(LSB)

XOR

INPUT

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式